DSTV Durbanville

Home › Blog › Signal and Dish

DStv Signal Settings and Frequencies Explained

Signal and DishBy our Durbanville DStv teamUpdated 21 October 20267 min read

Open the DStv signal settings screen and you'll see words like transponder, symbol rate and LNB type. Most of them you'll never touch. This guide explains what each one means, which single choice you actually make, and why typing in a frequency from the internet usually backfires.

Quick answer

DStv signal settings tell the decoder which satellite to listen to and what kind of LNB sits on your dish. In South Africa the satellite is Intelsat 20 at 68.5 degrees East, and the frequencies come preset. The one setting you choose is the LNB type: Single LNB for an HD decoder, Smart LNB for an Explora.

What DStv signal settings actually control

Think of the dish as an ear pointed at one spot in the sky. The settings tell the decoder how to make sense of what that ear hears. If they don't match the hardware on your roof, the decoder hears noise.

There are really only three groups of settings:

  • Satellite. Which satellite the dish faces. For DStv here, that's always Intelsat 20.
  • LNB type. The receiver on the dish arm. This tells the decoder how signal comes down the cable.
  • Frequency details. The channels the decoder tunes to on that satellite. These are preloaded.

Only the middle one is a real choice for most homes. The rest are there for technicians and special setups. If a decoder still misbehaves after the basics, our DStv repairs team can test it.

The DStv frequency fields, in plain words

A satellite doesn't send each channel separately. It sends groups of channels bundled together, and each bundle travels on its own frequency. The decoder needs a few numbers to find each bundle.

Field on screenWhat it meansShould you change it?
TransponderOne bundle of channels on the satelliteNo
FrequencyWhere that bundle sits on the dialNo
Symbol rateHow fast the data in that bundle is sentNo
PolarisationWhich way the signal wave is turnedNo
LNB typeThe kind of receiver on your dishYes, to match your hardware

So when someone searches for the DStv frequency and symbol rate, the honest answer is that a South African decoder already has them. Many lists online are written for other countries and other satellites. Entering those can leave your screen blank.

Technician tip

If you've already typed in new numbers and lost channels, don't keep guessing. A factory reset followed by the installation wizard puts the preset values back, and that's usually quicker than fixing each field.

DStv smart LNB frequency settings and user bands

An Explora has three tuners but only one cable from the dish. DStv's Smart LNB makes that possible with Unicable, which splits the cable into separate user bands. Each tuner gets its own band.

DStv lists two Smart LNB models. The LMX500 has 24 user bands, and the LMX501 has 30 user bands with 3 Unicable outputs and 1 Universal output. You don't assign these bands yourself. Once you select Smart LNB or Unicable, the Explora sorts them out.

Where an Explora keeps its DStv signal settings

On an Explora, press the DStv button, open Settings, then Satellite Settings. DStv's quick guide says the first-time wizard should show all three tuners with signal before you carry on. If one stays empty, the menu is rarely the culprit.

Moving up from an HD box? The old single LNB won't feed three tuners, so our Explora installation service swaps it out as part of the job.

Reading the screen after your DStv signal setup

Once the LNB type is set, the decoder shows two bars. Strength is how much signal arrives. Quality is how clean it is, and that's the number to trust.

Need DStv installers in Durbanville?

Tell us what you need or what your screen is showing. We give you a clear price before we drive out.

High strength with a jumpy quality bar usually means the dish is slightly off or something blocks its view. Our post on signal strength and quality readings explains what good numbers look like. If the wizard won't get past the signal screen at all, see our help for when you're stuck on the installation wizard.

When to redo the DStv signal setup in Durbanville

You only need to run through the DStv signal setup again when something physical changes. Around Durbanville, these are the usual triggers we see:

  1. You've swapped an HD decoder for an Explora, or the other way round.
  2. The decoder was reset to factory settings after a fault.
  3. You've moved into a new house in Sonstraal Heights, Vierlanden or Kenridge and brought your own decoder.
  4. A painter or roofer moved the dish during estate maintenance.
  5. A new LNB was fitted after a failure.

A move is a good time to have the dish checked too. Our DStv relocations and reconnections team sets up the decoder at the new address and confirms the readings.

Estates, complexes and the Tygerberg ridge

Plenty of Durbanville homes sit in security estates or sectional title complexes. Many share one dish through a block system. DStv says the Smart LNB isn't suitable for these shared setups, so the settings are different again.

If your complex in Bellville or Brackenfell runs a shared dish, our step-by-step page on entering communal dish settings walks you through it. Body corporates looking at an upgrade can read about our complex DStv installation work.

Homes high on the ridge near Plattekloof and Aurora usually have a clear view north-east. Lower down, a new double storey next door can creep into the dish's line of sight. No setting fixes a blocked view.

Safety first

Please don't go up a ladder or onto a double-storey roof to look at the dish, and never unscrew the LNB connectors or open the decoder. Winter rain makes tiles slick, and fine alignment needs a proper signal meter anyway.

Wet winter fronts can also cut the picture for a while. Our page on weather and DStv signal explains rain fade, and the E48-32 no signal fixes cover the safe checks to try first.

Need your DStv signal settings checked?

If you've picked the right LNB type, left the frequencies alone and the quality still won't hold, call a technician. Our DStv installation in Durbanville team covers Kraaifontein, Pinehurst, Welgedacht and the wine farms on the hills. We'll do satellite dish alignment on a meter and test every tuner with you.

Phone or WhatsApp 072 237 6363, or book a visit online. We quote before we drive out.

DStv signal settings: FAQs

What is the DStv frequency and symbol rate in South Africa?

South African decoders come with the frequency and symbol rate already loaded for Intelsat 20 at 68.5 degrees East. You don't need to enter them. Numbers found online are often for other countries and can wipe your channel list.

How do I set DStv signal settings manually?

Open the satellite or installation settings in the menu, confirm the satellite, and choose the LNB type that matches your dish. Leave the frequency fields as they are, check the quality bar, then scan for channels.

What are the DStv smart LNB frequency settings?

There aren't any to type in. A Smart LNB uses Unicable user bands, and the Explora assigns them to its tuners by itself. You only need to set the LNB type to Smart LNB or Unicable.

Why does my DStv keep losing signal after I change the settings?

Usually the LNB type doesn't match the hardware, or frequency fields were changed. A factory reset and a fresh wizard run restores the defaults. If the signal still drops, the dish or cable needs checking.

Can someone check my DStv signal settings in Durbanville?

Yes. Our technicians visit homes, estates and complexes across Durbanville and the northern suburbs. We check the menu, the LNB and the cable, then align the dish on a signal meter before we leave.

Talk to our Durbanville team

Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.