DSTV Durbanville

Home › Blog › OpenView

OpenView No Signal After a Storm: What to Check First

OpenViewBy our Durbanville DStv teamUpdated 11 October 20268 min read

A cold front rolls over the Tygerberg, the wind howls for a night, and in the morning the TV shows OpenView no signal. It's one of the most common calls we get in Durbanville each winter. Most of the time it's a quick fix you can do from the lounge, so start with the checks below before you book anyone.

Quick answer

For OpenView no signal after a storm, wait until the rain has fully stopped. Then switch off at the wall, unplug the dish cable and power from the decoder, plug the dish cable back first, then power, and let it reboot. If the HELP screen still shows 0% signal, the dish has probably moved and needs realigning.

Step one: give the weather time to clear

Heavy rain soaks up satellite signal before it reaches your dish. This is called rain fade, and OpenView itself says the picture comes back once the rain eases off. So if it's still bucketing down, put the kettle on and wait.

Thick cloud rarely kills the picture, but a downpour does. If the screen returns within an hour of the rain stopping, nothing is broken. Our no signal checklist covers the other quick checks.

The OpenView no signal reset that fixes most storm outages

If the sky is clear and the screen is still blank, power dips during the storm may have left the decoder confused. OpenView's own help and FAQ page suggests this simple reset:

  1. Switch the decoder off at the wall plug.
  2. Unplug the power cable and the dish cable from the back of the decoder.
  3. Wait about a minute.
  4. Plug the dish cable back in first and make sure it's snug.
  5. Plug the power back in, switch on and let the decoder reboot by itself.
  6. Give it a few minutes, then check if your channels are back.

Only touch the cables at the decoder end. Anything up at the dish is a job for a technician.

Check the signal screen when OpenView shows no signal

Press HELP on the OpenView remote. The help screen shows signal strength and quality near the bottom. OpenView says both should sit above 75% for smooth viewing, so these numbers tell you a lot.

What the help screen showsWhat it usually meansYour next move
Both readings above 75%Dish is fine, decoder needs a nudgeDo the reset above, then rescan channels from the menu
Readings jump around or sit lowDish slightly knocked, or water in a connectorWait for a dry day, then book a signal check
Both readings at 0%Dish pushed off target, cable cut or LNB damagedCall a technician to realign or repair
Picture only on channel 100Decoder lost its activationReactivate it, see the section below

Our older post on signal strength and quality readings explains these numbers in more depth. The idea is the same on OpenView and DStv.

Storm damage you can spot from the ground

Walk around the house and look up. You'll often see the problem without going anywhere near a ladder.

  • The dish faces a different way from the neighbours' dishes.
  • A branch or loose sheet is lying across the dish or the cable.
  • The cable is hanging loose, kinked or pulled out of its clips.
  • The wall plate or cable entry point is wet inside.
  • The decoder lights look odd, or it won't switch on at all after a lightning storm.

Safety first

Don't climb onto a wet roof or up a ladder to fix the dish yourself. Many Durbanville homes are double storeys with steep pitched roofs, and wet tiles are slippery. If there was lightning, unplug the decoder and TV and leave the outside cabling alone.

Need DStv installers in Durbanville?

Tell us what you need or what your screen is showing. We give you a clear price before we drive out.

Only channel 100 showing? Reactivate the decoder

Sometimes the storm itself isn't the problem. A long power cut can leave the decoder showing channel 100 and nothing else. That means it needs reactivating, not a new dish.

Press HELP to find your decoder's STB number and write it down. You can then reactivate online at openview.co.za, on WhatsApp or through the OpenView app. The decoder may reboot and update itself while it does this, so give it a few minutes.

Technician tip

Keep the STB number on a sticky note on the back of the remote. When the screen goes blank during a storm, you won't be hunting for it in the dark.

OpenView problems and solutions in Durbanville homes

These are the patterns we see across Durbanville and the northern suburbs after bad weather.

Windy ridges and open plots

Homes higher up towards the Tygerberg ridge and in Sonstraal Heights take the full force of a north-wester. A bracket that was a little loose can let the dish creep a few millimetres, and that's enough to drop the picture. Our satellite dish alignment service resets the angle on a proper meter and tightens everything for next winter.

Estates and complexes with one shared dish

In many Vierlanden and Kenridge complexes, units run off one shared dish. If every unit shows OpenView no signal at once, the fault is on the shared system, not in your lounge. Tell the body corporate or HOA, and ask about a check of the communal dish system.

Long cable runs on smallholdings

Out towards Welgedacht and the wine route, cables can run a long way from the dish to the house. Every outdoor joint is a place where water can creep in. Corroded connectors are a classic cause of OpenView signal problems that show up after a wet week.

When OpenView no signal needs a technician

Basic OpenView troubleshooting covers the reset, the help screen and reactivation. If you've done all three and the signal still reads zero on a dry day, something physical has moved or broken. Typical culprits are a dish knocked off target, a cracked LNB, a cut cable or a water-logged connector.

Our team handles OpenView installation and repairs across Bellville, Brackenfell, Kraaifontein and Durbanville. We check the dish on a signal meter, replace what's damaged and test every channel with you before we leave.

As a local team for DStv installation in Durbanville, we work on both systems, so a shared DStv and OpenView dish is no problem. If your DStv went down in the same storm, our guide on why weather knocks out signal covers that side.

Get your OpenView picture back

Try the reset and the help screen first. They solve most storm outages in a few minutes. If they don't, the dish needs a professional eye.

Send us a message through our contact page and tell us what the help screen shows. We'll quote first and often get out the same or next day, depending on the schedule. If this guide hasn't fixed it, call a technician rather than climbing up to the dish yourself.

OpenView no signal: FAQs

Why does my OpenView say no signal after rain?

Heavy rain blocks part of the satellite signal before it reaches the dish. This is called rain fade and it usually clears once the rain stops. If the picture doesn't come back within an hour of dry weather, do the cable reset and check the help screen readings.

How do I fix OpenView no signal without the remote?

The cable reset doesn't need the remote. Switch off at the wall, unplug the power and dish cables, plug the dish cable in first, then the power, and let the decoder reboot. You will need the remote to check signal levels or rescan channels, so replace the batteries if it has died.

What does E52 searching for signal mean on OpenView?

E52 means the decoder is looking for the satellite and can't find it. After a storm it is often rain fade or a knocked dish. Try the reset first. If the help screen still shows 0% signal on a dry day, the dish needs realigning.

Can a storm damage my OpenView decoder?

Yes, lightning and power surges can damage a decoder, even when the dish is fine. If the decoder won't power on or behaves strangely after a storm, unplug it and test it on another plug. A surge protector on the TV plug point is a cheap way to protect it next time.

Who can fix OpenView no signal in Durbanville?

Our local technicians repair OpenView dishes and cabling across Durbanville, Bellville, Brackenfell and Kraaifontein. We realign the dish on a signal meter, replace damaged parts and test with you before we leave. We give a quote before we drive out.

Talk to our Durbanville team

Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.